Hot Tub Electrical Installation in Etobicoke

Energo Electric wires hot tubs and swim spas across Etobicoke and The Kingsway: a new 240 volt circuit from your panel, a GFCI disconnect near the tub, bonding, the ESA permit and the inspection. Licensed electrical contractor, ECRA/ESA #7017134, 17 years in the trade, WSIB covered, $2 million liability insurance, 4.9 stars from 153 Google reviews. Call or text (416) 938-0322.

What a hot tub hookup includes

A dedicated breaker sized to the tub maker’s label, usually 40 or 50 amps for a 240 volt tub. Copper cable run from the panel to the yard, protected where it runs outside or underground. A GFCI disconnect within sight of the tub, set back from the water the distance the Ontario Electrical Safety Code requires. Bonding of the tub and nearby metal so there is no shock path. The ESA permit, the inspection and the certificate when it passes.

New electrical panel in an older Etobicoke home, installed by Energo Electric
Every hot tub circuit starts at the panel. This one is a new panel we installed in an older Etobicoke home.

Will my panel handle a hot tub?

Many Etobicoke homes still have 100 amp service. A hot tub adds a large load, so we do a load calculation before quoting. If the panel has room, the tub goes on its own breaker. If not, a 200 amp upgrade can be done at the same visit. Send us the tub model and a photo of your panel and we will tell you which one applies.

Before the tub arrives

Book the electrician before the delivery date so the circuit and disconnect are ready. Tell us where the tub will sit and the route from the panel to the yard. Keep the spot clear of overhead wires, and call Ontario One Call for a free locate before anyone digs a trench.

Send your tub model and a panel photo to (416) 938-0322 or send your job details. More: 100 vs 200 amp · Panel upgrades · ESA permits · Residential · The Kingsway

ECRA/ESA Licensed Electrical Contractor #7017134. Every job permitted and inspected. Email contact@energoelectric.ca.

Hot tub wiring questions

Do I need an electrician to install a hot tub in Ontario?

Yes for any hard wired hot tub. A 240 volt tub needs a new circuit, a GFCI disconnect and bonding, and the work needs an ESA permit and inspection. Only a Licensed Electrical Contractor may be hired to do it. Small 120 volt plug in tubs still need a proper GFCI protected outlet in the right spot.

What size breaker does a hot tub need?

Most 240 volt hot tubs need a 40 or 50 amp breaker, and some larger tubs and swim spas need 60 amps or more. The correct size is on the tub maker’s label and in the install manual, and the wire size follows from it. We confirm it from your tub model before quoting.

How far does the disconnect have to be from the hot tub?

The Ontario Electrical Safety Code requires the disconnect to be within sight of the tub but set back a minimum distance from the water so nobody can reach it from inside the tub. We place it to meet the code and the tub maker’s instructions, and the ESA inspector checks it.

Can a hot tub go on a 100 amp panel?

Sometimes. It depends on what else the house runs. A load calculation tells us if there is room. If there is not, a 200 amp upgrade can be done at the same time as the hot tub hookup, with one ESA permit.

Before your hot tub arrives

How far does a hot tub have to be from outlets and power lines?

ESA says existing electrical equipment must be three metres away from a pool or hot tub unless a fence, wall or permanent barrier separates them. The tub must also meet the clearances from overhead power and communication lines, which the local utility sets, and some utilities do not allow one under a power line at all. Send us a photo of the spot before the tub is delivered.

Why does my hot tub keep tripping the breaker?

A GFCI that trips is doing its job: it has found current leaking where it should not. Common causes are a failing heater element, water in the pump or the wiring box, a worn out GFCI or a loose connection. Do not keep resetting it and never bypass it. Leave the tub off and have it tested.

How do I know if my hot tub is 120 volt or 240 volt?

Read the nameplate on the tub or the install manual. A 120 volt plug in tub has a cord with a built in GFCI and uses a standard outlet on its own circuit. A 240 volt tub has no plug. It is hard wired to a GFCI protected disconnect and needs a new circuit, an ESA permit and an inspection.

Call (416) 938-0322Get my fixed price