100 Amp or 200 Amp Panel: Which Does Your Home Need?

If your home still runs on 100 amps and you plan to add an EV charger, a heat pump, central air, an induction range, a hot tub or a basement suite, you may need 200 amps. If nothing big is being added, 100 amps is often enough. The honest answer comes from a load calculation under the Ontario Electrical Safety Code, not from the size of the house.

Written by Energo Electric Inc., licensed electrical contractor in Etobicoke and The Kingsway, ECRA/ESA #7017134, 17 years in the trade.

Eaton electrical panel upgrade by Energo Electric in Etobicoke
A panel upgrade our crew finished in Etobicoke.
New breaker panel with neatly labelled circuits and dressed wiring
New breaker panel with labelled circuits.

Why so many Etobicoke homes have 100 amps

Many houses in The Kingsway, Islington Village, Humber Valley and the rest of Etobicoke were built or last updated when 60 or 100 amps was normal. Back then there were no EV chargers, few air conditioners and gas did most of the heavy work. Today more of a home runs on electricity, so the same panel has more to carry.

Signs you are outgrowing 100 amps

The main breaker trips when several big appliances run together. There is no room left in the panel for new breakers. You are adding an EV charger, heat pump, hot tub, induction range or a second kitchen. The panel is an older brand with known problems, such as Federal Pioneer Stab-Lok. Lights dim when the air conditioner or dryer starts.

How the decision is made

A licensed electrician adds up your existing loads and the new ones using the method in the Ontario Electrical Safety Code. If the total fits within 100 amps, you keep your service and add a breaker or a load manager. If it does not fit, you upgrade to 200 amps. A load manager can sometimes add an EV charger to a 100 amp panel without an upgrade by pausing charging when the house is busy.

What a 200 amp upgrade involves

A new panel and main breaker, often a new meter base and service cable, and new grounding. The utility, such as Toronto Hydro, disconnects and reconnects power, and the work needs an ESA permit and inspection. Many upgrades are done in one day with the power off for part of it. Energo files the permit, books the utility and gives you one written price before work starts.

Send a photo of your panel to (416) 938-0322 or send your job details. More: Panel upgrades · EV charger on a 100 amp panel · Stab-Lok panels · ESA permits · The Kingsway

ECRA/ESA Licensed Electrical Contractor #7017134. Every job permitted and inspected. Email contact@energoelectric.ca.

100 amp vs 200 amp questions

Is 100 amp service enough for a house in Ontario?

Often, yes, for a home with gas heat, gas water heating and no EV charger. It becomes tight when you add an EV charger, heat pump, central air, induction cooking, a hot tub or a second unit. A load calculation under the Ontario Electrical Safety Code tells you for sure, and a licensed electrician can do it from your appliance list and a panel photo.

Can I add an EV charger without upgrading to 200 amps?

Sometimes. If the load calculation shows room, the charger goes on its own circuit. If it is close, a load manager can watch the house load and pause the charger when needed, which the Ontario code allows. If there is no room at all, a 200 amp upgrade is the clean fix.

How long does a 200 amp upgrade take?

Many homes are done in one working day. The power is off for part of that day while the utility disconnects and reconnects the service. The ESA permit is filed before work starts and the inspection follows.

Do I need a permit to upgrade my panel?

Yes. A panel or service upgrade always needs an ESA permit and inspection, and the utility must be booked to disconnect and reconnect power. The licensed contractor arranges both.

Call (416) 938-0322Get my fixed price